Garage Door Opener Repair in Glendale, CA
Opener acting up in Glendale? Often the opener isn't to blame: a door that's out of balance makes it strain until something gives. We check the door first, then repair the opener so it lasts.
Licensed & insured · Free estimates · Visits booked to suit you
Garage Door Opener Repair for Glendale Homes
If your opener in Glendale hums, clicks or sends the door back up for no reason, stop pressing the button and give us a call. We'll track down the cause, whether it's the motor unit, the safety sensors, the remote or the door itself. When a repair isn't worth it, we'll say so and quote a replacement on the spot.
Dust blown in by the wind in Glendale is a common reason the safety sensors stop seeing each other. Cleaning and realigning them is often all it takes to get your opener working again.
Chain Drive, Belt Drive and Wall-Mount Openers
Chain drive openers are durable workhorses and the loudest type. Their chains stretch over time and need occasional tightening. Belt drive openers use a reinforced rubber belt and run much more quietly, which matters if there's a bedroom over the garage. Screw drive units turn a threaded rod that needs to stay lubricated, and plenty are still in service.
Wall-mount (jackshaft) openers sit on the wall beside the torsion shaft instead of on the ceiling. They keep the ceiling clear for storage and only work with torsion spring doors. Whichever type you have, we can repair it.
Common Garage Door Opener Problems
What we see most often, and what usually causes it:
- Motor runs, door doesn't move: a stripped drive gear, a broken trolley, or a snapped chain or belt.
- Door reverses as soon as it touches the floor: the down travel limit is set too far or the force is set too low.
- Door won't close and the opener light flashes: the photo-eye sensors are blocked, dirty, out of alignment or have a broken wire.
- Nothing happens at all: a power problem, a tripped GFCI outlet, a failed capacitor or a dead logic board.
- Works from the wall button but not the remote: a dead remote battery, lost programming or a failing receiver.
- Works on and off in hot weather: a circuit board or capacitor on its way out, which a hot Southern California garage exposes fast.
- Grinding from the motor unit: the drive gear is wearing itself out, and the sprocket may be next.
Garage Door Safety Sensor Problems
Every opener made since 1993 has photo-eye safety sensors mounted about six inches off the floor on each side of the door. They're a federal requirement, and they're the most common reason a door refuses to close.
The cause is usually simple: a bike leaning against one, a cobweb on a lens, afternoon sun shining into the receiver, or a bracket that got bumped. Sometimes a wire is pinched or chewed. We realign or repair the sensors and keep them working, because an opener without working sensors can close on a pet or a child.
Learn more about garage door opener repair →
Serving Glendale From Our Anaheim Shop
Our shop is in Anaheim, and we serve Glendale with visits booked at a time that suits you. Tell us what the door is doing and we'll come prepared for the repair.
Every job starts with a free estimate, and you get a firm price before any work begins. We're a licensed and insured, family-owned company, and the father-and-son team who quotes your job is usually the one who does the work.
As Cathy Zavala put it: “Roberto and his son were great! Great experience, service and price.”
Common Questions About Garage Door Opener Repair in Glendale
Do you offer garage door opener repair in Glendale?
Yes. We serve Glendale from our Anaheim shop and book opener repairs at a time that suits you. Call (714) 880-7574 and tell us what the door is doing.
Why does my garage door go down and then back up?
The opener is sensing resistance on the way down and reversing for safety. The cause is usually something in the door's path, a sensor issue, a misadjusted force or travel limit, or the door binding in the track. If it reverses right as it touches the floor, it's almost always a limit setting, which is a quick adjustment.
Why does my garage door opener hum but not open?
A humming motor with no movement usually means the drive gear is stripped. The motor is turning, but nothing is driving the trolley. It's a common repair on most chain and belt openers, and it costs far less than a new opener.
Can you fix an opener with no brand name on it?
Almost always. Most openers come from a handful of manufacturers, and gears, sensors and boards are shared across model families. Send us a photo of the label on the side of the motor unit and we can usually identify it.
How much does garage door opener repair cost in Glendale?
It depends on what has failed: a gear, a sensor, a circuit board or the door itself. Many opener repairs can be priced over the phone once you describe what's happening, and you always get a firm price before any work starts.
Garage Door Opener Repair Near Glendale
Live just outside Glendale? We serve these nearby cities too.